Logo

Home | Audio | DIY | Guitar | iPods | Music | Brain/Problem Solving | Links| Site Map

This work is licensed under a Creative Commons License.

iPod Headphone Jack and Hold Switch Repair

More iPod How To's

Introduction

Each step has a bullet indicating the tool you'll be using. Don't worry about getting lost or confused; hundreds of people have successfully used the Fixit Guide series to repair their laptops.


Tools used in this guide

* iPod Opening Tools
* Phillips #00 Screwdriver

Parts relevant to this guide

* iPod Video 30 GB Headphone Jack & Hold Switch
* iPod Video 60/80 GB Headphone Jack & Hold Switch

Hold on

Step 1 — Battery

Before opening your iPod, ensure that the hold switch is in the locked position.

Taking It apart

Step 2

Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened.

Insert a plastic iPod opening tool in the seam between the plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the tabs holding the iPod together.

Taking It Apart 2

Step 3

Continue to run the opening tool along the side of the case until all the tabs have been released.

Taking it apart again

Step 4

Work around the corner of the iPod and release the single tab near the hold switch.

taking it apart

Step 5

Free the tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

Ribbon wire beware

Step 6

The iPod casing is now open, but don't separate the two halves just yet. There are two ribbon cables connecting the rear panel to the rest of the iPod.

Use a spudger to slide up the brown connector holding the orange battery ribbon in place. You only need to lift the brown locking bar up about 2mm to free the cable.

Battery Connector

Step 7

Slide the orange battery ribbon out of its connector.

Careful

Step 8

Place the rear panel next to the iPod, being careful not to strain the orange headphone jack cable.

Headphone Jack Ribbon Cable

Step 9

Lift the hard drive up with one hand so you can access the headphone jack ribbon beneath.
Use a spudger to flip up the brown plastic tab holding the headphone jack ribbon in place. The brown tab will rotate up 90 degrees, releasing the ribbon cable.

Connectors

Step 10

Slide the orange headphone jack ribbon out of its connector.

The rear panel is now free from the iPod.

img

Step 11

The battery is attached to the rear panel with adhesive. Be careful not to tear the orange headphone jack ribbon when removing the battery.

Lift the battery and the attached orange cable out of the iPod. If you have a 60 or 80 GB iPod, the battery will be thicker than the one pictured.

img

Step 12 Headphone Jack & Hold Switch

Peel up the black tape securing the orange headphone ribbon cable to the rear panel.

img

Step 13

Remove the two black Phillips screws securing the headphone jack to the lower casing.

img

Step 14

Remove the following two screws
One black Phillips screw securing the hold switch near the corner of the iPod.
One silver Phillips screw securing the other side of the hold switch.

img

Step 15

Lift the hold switch free of its housing on the rear panel. Don't remove the hold switch completely at this time because it is connected to the same cable as the headphone jack.

img

Step 16

Slide the headphone jack out of its housing on the rear panel.

img

Step 17

Lift the headphone jack and hold switch assembly out of the iPod.

img

Step 18

If your replacement headphone jack includes the white plastic hold switch, simply reinstall the headphone jack now.
If your replacement part does not include the plastic hold switch, follow the next steps to transfer the plastic hold switch to your new headphone jack.
Remove the single Phillips screw nearest to the hold switch.
Lift the plastic hold switch away from the orange ribbon cable.

img

Step 19

Carefully peel the orange ribbon cable and attached black hold switch up from the metal backing.
Attach the replacement hold switch unit to the silver metal backing, making sure the two small posts on the back of the hold switch are aligned with the two holes in the metal backing.

Congratulations! You have now removed your item. To reassemble simply follow the directions in reverse order.

Compiled by Johnny P.

More iPod How To's

Home | Audio | DIY | Guitar | iPods | Music | Links | Brain and Problem Solving | Site Map | Contact

Top

Creative Commons License